General Information
This subject covers an introduction to the current Standard Method of Measurement of Building Works used in Australia, methods of recording building dimensions, checking building plans and specifications and the measurement of necessary trades including concrete, masonry, finishes, carpentry and roofing.
-
Details
Academic unit: Faculty of Society & Design Subject code: SSUD71-317 Subject title: Measurement 1 Subject level: Postgraduate Semester/Year: May 2023 Credit points: 10.000 -
Delivery & attendance
Timetable: https://bond.edu.au/timetable Delivery mode: Intensive Workload items: - Workshop: x3 (Total hours: 18) - Workshop 1: 3 days
- Workshop: x3 (Total hours: 18) - Workshop 2: 3 days
- Personal Study Hours: x12 (Total hours: 84) - Recommended study hours
Attendance and learning activities: As successful completion of this subject is heavily dependent on participation during all scheduled sessions, attendance will be monitored. Most sessions build on the content of the previous one. It is difficult for a student to recover if a session is missed. It is the responsibility of the student to catch up on any content missed and to complete set work outside class. It is also necessary for students to engage proactively and contribute positively in discussions, analyses and case studies. The assessments are an important part of developing the knowledge and understanding required to fulfil the minimum requirements of this subject. In addition to face-to-face contact time, students should plan to spend a minimum of 84 hours undertaking preparation/out of class work/personal study for this subject. This is intended as a general guide only for workload planning. More time may be required depending on the student's comprehension of the content delivered in class and aptitude for the subject. Please note that subsequent subjects assume the student has a full understanding of this subject - this content will not be repeated. -
Resources
Prescribed resources: Books
- Australian and New Zealand standard method of measurement of building works. ANZSMM 2022, Sydney, NSW The Australian Institute of Quantity Surveyors Ltd
- Rick Best,Peter Smith,Judy Doherty (2020). Detailed Building Measurement. 2nd, Sydney, N.S.W. AIQS 272
iLearn@Bond & Email: iLearn@Bond is the Learning Management System at Bond University and is used to provide access to subject materials, class recordings and detailed subject information regarding the subject curriculum, assessment, and timing. Both iLearn and the Student Email facility are used to provide important subject notifications.
Additionally, official correspondence from the University will be forwarded to students’ Bond email account and must be monitored by the student.
To access these services, log on to the Student Portal from the Bond University website as www.bond.edu.au
| Academic unit: | Faculty of Society & Design |
|---|---|
| Subject code: | SSUD71-317 |
| Subject title: | Measurement 1 |
| Subject level: | Postgraduate |
| Semester/Year: | May 2023 |
| Credit points: | 10.000 |
| Timetable: | https://bond.edu.au/timetable |
|---|---|
| Delivery mode: | Intensive |
| Workload items: |
|
| Attendance and learning activities: | As successful completion of this subject is heavily dependent on participation during all scheduled sessions, attendance will be monitored. Most sessions build on the content of the previous one. It is difficult for a student to recover if a session is missed. It is the responsibility of the student to catch up on any content missed and to complete set work outside class. It is also necessary for students to engage proactively and contribute positively in discussions, analyses and case studies. The assessments are an important part of developing the knowledge and understanding required to fulfil the minimum requirements of this subject. In addition to face-to-face contact time, students should plan to spend a minimum of 84 hours undertaking preparation/out of class work/personal study for this subject. This is intended as a general guide only for workload planning. More time may be required depending on the student's comprehension of the content delivered in class and aptitude for the subject. Please note that subsequent subjects assume the student has a full understanding of this subject - this content will not be repeated. |
| Prescribed resources: | Books
|
|---|---|
| iLearn@Bond & Email: | iLearn@Bond is the Learning Management System at Bond University and is used to provide access to subject materials, class recordings and detailed subject information regarding the subject curriculum, assessment, and timing. Both iLearn and the Student Email facility are used to provide important subject notifications. Additionally, official correspondence from the University will be forwarded to students’ Bond email account and must be monitored by the student. To access these services, log on to the Student Portal from the Bond University website as www.bond.edu.au |
Enrolment requirements
| Requisites: |
Pre-requisites:Co-requisites:There are no co-requisites |
|---|---|
| Assumed knowledge: |
Assumed knowledge is the minimum level of knowledge of a subject area that students are assumed to have acquired through previous study. It is the responsibility of students to ensure they meet the assumed knowledge expectations of the subject. Students who do not possess this prior knowledge are strongly recommended against enrolling and do so at their own risk. No concessions will be made for students’ lack of prior knowledge.
|
| Restrictions: |
Nil |
Assurance of learning
Assurance of Learning means that universities take responsibility for creating, monitoring and updating curriculum, teaching and assessment so that students graduate with the knowledge, skills and attributes they need for employability and/or further study.
At Bond University, we carefully develop subject and program outcomes to ensure that student learning in each subject contributes to the whole student experience. Students are encouraged to carefully read and consider subject and program outcomes as combined elements.
Program Learning Outcomes (PLOs)
Program Learning Outcomes provide a broad and measurable set of standards that incorporate a range of knowledge and skills that will be achieved on completion of the program. If you are undertaking this subject as part of a degree program, you should refer to the relevant degree program outcomes and graduate attributes as they relate to this subject.
Subject Learning Outcomes (SLOs)
On successful completion of this subject the learner will be able to:
- Understand and apply the basic principles of the measurement of building works and gain an appreciation of its role as a basis for the financial management of building contracts.
- Critically analyse standard contract documents (drawings and specification) for basic and complex building works and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.
Generative Artificial Intelligence in Assessment
The University acknowledges that Generative Artificial Intelligence (Gen-AI) tools are an important facet of contemporary life. Their use in assessment is considered in line with students’ development of the skills and knowledge which demonstrate learning outcomes and underpin study and career success. Instructions on the use of Gen-AI are given for each assessment task; it is your responsibility to adhere to these instructions.
-
Assessment details
Type Task % Timing* Outcomes assessed Paper-based Examination (Limited Open) End of semester examination 50.00% Final Examination Period 1,2,3 Technical Document Paper based quantities take-off 10.00% Week 4 1,2,3 Computer-aided Test (Limited Open) iLearn test 10.00% Week 5 1,3 Computer-aided Test (Limited Open) iLearn test 10.00% Week 9 1,3 Technical Document§ Quantities take off and bills of quantities using industry standard software 20.00% Week 10 1,2,3,4 - § Indicates group/teamwork-based assessment
- * Assessment timing is indicative of the week that the assessment is due or begins (where conducted over multiple weeks), and is based on the standard University academic calendar
- C = Students must reach a level of competency to successfully complete this assessment.
-
Assessment criteria
Assessment criteria
High Distinction 85-100 Outstanding or exemplary performance in the following areas: interpretative ability; intellectual initiative in response to questions; mastery of the skills required by the subject, general levels of knowledge and analytic ability or clear thinking. Distinction 75-84 Usually awarded to students whose performance goes well beyond the minimum requirements set for tasks required in assessment, and who perform well in most of the above areas. Credit 65-74 Usually awarded to students whose performance is considered to go beyond the minimum requirements for work set for assessment. Assessable work is typically characterised by a strong performance in some of the capacities listed above. Pass 50-64 Usually awarded to students whose performance meets the requirements set for work provided for assessment. Fail 0-49 Usually awarded to students whose performance is not considered to meet the minimum requirements set for particular tasks. The fail grade may be a result of insufficient preparation, of inattention to assignment guidelines or lack of academic ability. A frequent cause of failure is lack of attention to subject or assignment guidelines. Quality assurance
For the purposes of quality assurance, Bond University conducts an evaluation process to measure and document student assessment as evidence of the extent to which program and subject learning outcomes are achieved. Some examples of student work will be retained for potential research and quality auditing purposes only. Any student work used will be treated confidentially and no student grades will be affected.
| Type | Task | % | Timing* | Outcomes assessed |
|---|---|---|---|---|
| Paper-based Examination (Limited Open) | End of semester examination | 50.00% | Final Examination Period | 1,2,3 |
| Technical Document | Paper based quantities take-off | 10.00% | Week 4 | 1,2,3 |
| Computer-aided Test (Limited Open) | iLearn test | 10.00% | Week 5 | 1,3 |
| Computer-aided Test (Limited Open) | iLearn test | 10.00% | Week 9 | 1,3 |
| Technical Document§ | Quantities take off and bills of quantities using industry standard software | 20.00% | Week 10 | 1,2,3,4 |
- § Indicates group/teamwork-based assessment
- * Assessment timing is indicative of the week that the assessment is due or begins (where conducted over multiple weeks), and is based on the standard University academic calendar
- C = Students must reach a level of competency to successfully complete this assessment.
Assessment criteria
| High Distinction | 85-100 | Outstanding or exemplary performance in the following areas: interpretative ability; intellectual initiative in response to questions; mastery of the skills required by the subject, general levels of knowledge and analytic ability or clear thinking. |
|---|---|---|
| Distinction | 75-84 | Usually awarded to students whose performance goes well beyond the minimum requirements set for tasks required in assessment, and who perform well in most of the above areas. |
| Credit | 65-74 | Usually awarded to students whose performance is considered to go beyond the minimum requirements for work set for assessment. Assessable work is typically characterised by a strong performance in some of the capacities listed above. |
| Pass | 50-64 | Usually awarded to students whose performance meets the requirements set for work provided for assessment. |
| Fail | 0-49 | Usually awarded to students whose performance is not considered to meet the minimum requirements set for particular tasks. The fail grade may be a result of insufficient preparation, of inattention to assignment guidelines or lack of academic ability. A frequent cause of failure is lack of attention to subject or assignment guidelines. |
Quality assurance
For the purposes of quality assurance, Bond University conducts an evaluation process to measure and document student assessment as evidence of the extent to which program and subject learning outcomes are achieved. Some examples of student work will be retained for potential research and quality auditing purposes only. Any student work used will be treated confidentially and no student grades will be affected.
Study Information
Submission procedures
Students must check the iLearn@Bond subject site for detailed assessment information and submission procedures.
Policy on late submission and extensions
A student who has not established a basis for an extension in compliance with University and Faculty policy either by 1) not applying before the assessment due date or 2) by having an application rejected due to failure to show a justifiable cause for an extension, will receive a penalty on assessment submitted after its due date. The penalty will be 10% of marks awarded to that assessment for every day late, with the first day counted after the required submission time has passed. No assessment will be accepted for consideration seven calendar days after the due date. Where a student has been granted an extension, the late penalty starts from the new due date and time set out in the extension.
Academic Integrity
Bond University‘s Student Code of Conduct Policy , Student Charter, Academic Integrity Policy and our Graduate Attributes guide expectations regarding student behaviour, their rights and responsibilities. Information on these topics can be found on our Academic Integrity webpage recognising that academic integrity involves demonstrating the principles of integrity (honesty, fairness, trust, professionalism, courage, responsibility, and respect) in words and actions across all aspects of academic endeavour.
Staff are required to report suspected misconduct. This includes all types of plagiarism, cheating, collusion, fabrication or falsification of data/content or other misconduct relating to assessment such as the falsification of medical certificates for assessment extensions. The longer term personal, social and financial consequences of misconduct can be severe, so please ask for help if you are unsure.
If your work is subject to an inquiry, you will be given an opportunity to respond and appropriate support will be provided. Academic work under inquiry will not be marked until the process has concluded. Penalties for misconduct include a warning, reduced grade, a requirement to repeat the assessment, suspension or expulsion from the University.
Feedback on assessment
Feedback on assessment will be provided to students according to the requirements of the Assessment Procedure Schedule A - Assessment Communication Procedure.
Whilst in most cases feedback should be provided within two weeks of the assessment submission due date, the Procedure should be checked if the assessment is linked to others or if the subject is a non-standard (e.g., intensive) subject.
Accessibility and Inclusion Support
Support is available to students where a physical, mental or neurological condition exists that would impact the student’s capacity to complete studies, exams or assessment tasks. For effective support, special requirement needs should be arranged with the University in advance of or at the start of each semester, or, for acute conditions, as soon as practicable after the condition arises. Reasonable adjustments are not guaranteed where applications are submitted late in the semester (for example, when lodged just prior to critical assessment and examination dates).
As outlined in the Accessibility and Inclusion Policy, to qualify for support, students must meet certain criteria. Students are also required to meet with the Accessibility and Inclusion Advisor who will ensure that reasonable adjustments are afforded to qualifying students.
For more information and to apply online, visit BondAbility.
Additional subject information
Subject curriculum
-
Introduction to Measurement 1
Introduction to the subject and ANZSMM.
SLOs included
- Understand and apply the basic principles of the measurement of building works and gain an appreciation of its role as a basis for the financial management of building contracts.
-
Measurement procedure
Measurement conventions, procedures and general rules.
SLOs included
- Understand and apply the basic principles of the measurement of building works and gain an appreciation of its role as a basis for the financial management of building contracts.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
-
Finishes
Measurement of Interior finishes.
SLOs included
- Critically analyse standard contract documents (drawings and specification) for basic and complex building works and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.
-
Concrete
Measurement of in-situ concrete elements.
SLOs included
- Critically analyse standard contract documents (drawings and specification) for basic and complex building works and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.
-
Formwork
Measurement of formwork.
SLOs included
- Critically analyse standard contract documents (drawings and specification) for basic and complex building works and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.
-
Reinforcement
Measurement of reinforcement in concrete.
SLOs included
- Critically analyse standard contract documents (drawings and specification) for basic and complex building works and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.
-
Masonry
Measurement of brickwork and blockwork.
SLOs included
- Critically analyse standard contract documents (drawings and specification) for basic and complex building works and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.
-
Carpentry
Measurement of timber floor, wall and roof framing and sheet linings.
SLOs included
- Critically analyse standard contract documents (drawings and specification) for basic and complex building works and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.
-
Roofing
Measurement of sheet metal and tiled roofing systems, measurement of roof plumbing systems.
SLOs included
- Critically analyse standard contract documents (drawings and specification) for basic and complex building works and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of building works.
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.
-
Introduction to Computer Applications
Introduction to industry estimating software.
SLOs included
- Apply the rules and principles described in the Standard Method of Measurement to prepare accurate quantities and descriptions for the measurement of building works and to produce Bills of Quantities, using industry standard software.