This subject covers an introduction to the Australian Standard Method of Measurement, methods of recording building dimensions, checking building plans and specifications, measurement of basic trades including brickwork, finishes, earthworks, concrete and roofing.
|Academic unit:||Faculty of Society & Design|
|Subject title:||Measurement 1|
Delivery & attendance
|Attendance and learning activities:||Attend all lectures and tutorials. Most sessions build on the work of the previous one. It is difficult to recover if a session is missed. Attendance in lectures and tutorials will be monitored, and could impact the final mark in this subject.|
|Prescribed resources:|| |
|[email protected] & Email:||[email protected] is the online learning environment at Bond University and is used to provide access to subject materials, lecture recordings and detailed subject information regarding the subject curriculum, assessment and timing. Both iLearn and the Student Email facility are used to provide important subject notifications. Additionally, official correspondence from the University will be forwarded to students’ Bond email account and must be monitored by the student.|
To access these services, log on to the Student Portal from the Bond University website as www.bond.edu.au
|Restrictions: ?|| This subject is not available to|
Assurance of learning
Assurance of Learning means that universities take responsibility for creating, monitoring and updating curriculum, teaching and assessment so that students graduate with the knowledge, skills and attributes they need for employability and/or further study.
At Bond University, we carefully develop subject and program outcomes to ensure that student learning in each subject contributes to the whole student experience. Students are encouraged to carefully read and consider subject and program outcomes as combined elements.
Program Learning Outcomes (PLOs)
Program Learning Outcomes provide a broad and measurable set of standards that incorporate a range of knowledge and skills that will be achieved on completion of the program. If you are undertaking this subject as part of a degree program, you should refer to the relevant degree program outcomes and graduate attributes as they relate to this subject.
Subject Learning Outcomes (SLOs)
On successful completion of this subject the learner will be able to:
- Understand the basic principles of measurement of building works and its role as a basis for the financial management of building contracts.
- Analyse standard contract documents (drawings and specification) and extract information relevant to the measurement and construction of the works described.
- Demonstrate knowledge and understanding of the principles of the measurement of simple building works.
- Prepare quantities for the measurement of building works using the rules and principles described in the Australian Standard Method of Measurement.
|Skills Assignment||4 x Skills Assignments at 2.5% weighting each. Further details will be provided on iLearn.||10%||Progressive||1, 2, 3, 4.|
|Technical Document||Measurement of Surfaces and Volumes||10%||Week 3||1.|
|Technical Document||Quantities take-off with BQ, using standard industry software.||20%||Week 10||1, 2, 3, 4.|
|Paper-based Examination (Limited Open) ^||Final Examination||40%||Final Examination Period||1, 2, 3, 4.|
|Paper-based Examination (Limited Open)||Quantities take-off and short answer questions||20%||Week 7 (Mid-Semester Examination Period)||1, 2, 3, 4.|
To pass this subject students must achieve a minimum 50% mark in both the mid-semester and end of semester exams, with an aggregate mark of 50% or above in all other assessments. Where a student achieves an overall mark of 50% or more but fails an exam a final result of 46F will be recorded.
- ^ Students must pass this assessment to pass the subject
- * Assessment timing is indicative of the week that the assessment is due or begins (where conducted over multiple weeks), and is based on the standard University academic calendar
- C = Students must reach a level of competency to successfully complete this assessment.
|High Distinction||85-100||Outstanding or exemplary performance in the following areas: interpretative ability; intellectual initiative in response to questions; mastery of the skills required by the subject, general levels of knowledge and analytic ability or clear thinking.|
|Distinction||75-84||Usually awarded to students whose performance goes well beyond the minimum requirements set for tasks required in assessment, and who perform well in most of the above areas.|
|Credit||65-74||Usually awarded to students whose performance is considered to go beyond the minimum requirements for work set for assessment. Assessable work is typically characterised by a strong performance in some of the capacities listed above.|
|Pass||50-64||Usually awarded to students whose performance meets the requirements set for work provided for assessment.|
|Fail||0-49||Usually awarded to students whose performance is not considered to meet the minimum requirements set for particular tasks. The fail grade may be a result of insufficient preparation, of inattention to assignment guidelines or lack of academic ability. A frequent cause of failure is lack of attention to subject or assignment guidelines.|
For the purposes of quality assurance, Bond University conducts an evaluation process to measure and document student assessment as evidence of the extent to which program and subject learning outcomes are achieved. Some examples of student work will be retained for potential research and quality auditing purposes only. Any student work used will be treated confidentially and no student grades will be affected.
Students must check the [email protected] subject site for detailed assessment information and submission procedures.
Policy on late submission and extensions
A late penalty will be applied to all overdue assessment tasks unless an extension is granted by the subject coordinator. The standard penalty will be 10% of marks awarded to that assessment per day late with no assessment to be accepted later than seven days after the due date. Where a student is granted an extension, the penalty of 10% per day late starts from the extended due date.
Policy on plagiarism
University’s Academic Integrity Policy defines plagiarism as the act of misrepresenting as one’s own original work: another’s ideas, interpretations, words, or creative works; and/or one’s own previous ideas, interpretations, words, or creative work without acknowledging that it was used previously (i.e., self-plagiarism). The University considers the act of plagiarising to be a breach of the Student Conduct Code and, therefore, subject to the Discipline Regulations which provide for a range of penalties including the reduction of marks or grades, fines and suspension from the University.
Feedback on assessment
Feedback on assessment will be provided to students within two weeks of the assessment submission due date, as per the Assessment Policy.
If you have a disability, illness, injury or health condition that impacts your capacity to complete studies, exams or assessment tasks, it is important you let us know your special requirements, early in the semester. Students will need to make an application for support and submit it with recent, comprehensive documentation at an appointment with a Disability Officer. Students with a disability are encouraged to contact the Disability Office at the earliest possible time, to meet staff and learn about the services available to meet your specific needs. Please note that late notification or failure to disclose your disability can be to your disadvantage as the University cannot guarantee support under such circumstances.
Subject outline, Introduction to ASMM
Measurement of floor and wall finishes
Measurement of in-situ concrete
Measurement of formwork
Measurement of reinforcement to concrete
Introduction to Buildsoft Software
Measurement of Brickwork
Introduction to Buildsoft Software
Measurement of Carpentry items
Measurement of Carpentry items
Measurement of Roofing and Roof Plumbing