This subject addresses the importance of using BIM/Lean/IPD to optimise design quality to ensure it meets client brief standards. It also covers the management of quality during the construction phase by early identification and design rectification of potential coordination clashes and the like, thereby ensuring delivery on two fundamental Lean Construction principles - eliminating defects and eliminating waiting time on-site during construction. The subject also addresses how BIM models and Lean construction approaches in a collaborative IPD approach can significantly enhance the ability to identify and facilitate elimination/management of potential safety risks that might otherwise manifest during construction of the project. The subject is taught in a highly interactive environment dedicated to aspects of utilising BIM technology platforms to identify opportunities for design quality improvement and identification of potential construction and operation period safety concerns, and elimination of those concerns. The subject introduces students to using BIM/Lean/IPD principles to ensure project processes ensure minimisation of waste and optimum timeliness of making the necessary change concerning design adjustments and safety risk elimination.
|Academic unit:||Faculty of Society & Design|
|Subject title:||Continuous Process Improvement (Quality and Safety Standards)|
Delivery & attendance
|Attendance and learning activities:||As successful completion of this subject is heavily dependent on participation during all scheduled sessions, attendance will be monitored. Most sessions build on the content of the previous one. It is difficult for a student to recover if a session is missed. It is the responsibility of the student to catch up on any content missed and to complete set work outside class. It is also necessary for students to engage proactively and contribute positively in discussions, analyses and case studies. The assessments are an important part of developing the knowledge and understanding required to fulfil the minimum requirements of this subject. In addition to ‘remote’ face-to-face contact time, students should plan to spend a minimum of 84 hours undertaking preparation/out of class work/personal study for this subject. This is intended as a general guide only for workload planning. More time may be required depending on the student's comprehension of the content delivered in class and aptitude for the subject. Please note that subsequent subjects assume the student has a full understanding of this subject - this content will not be repeated.|
|Prescribed resources:||No Prescribed resources. After enrolment, students can check the Books and Tools area in iLearn for the full Resource List.|
|[email protected] & Email:||[email protected] is the online learning environment at Bond University and is used to provide access to subject materials, lecture recordings and detailed subject information regarding the subject curriculum, assessment and timing. Both iLearn and the Student Email facility are used to provide important subject notifications. Additionally, official correspondence from the University will be forwarded to students’ Bond email account and must be monitored by the student.|
To access these services, log on to the Student Portal from the Bond University website as www.bond.edu.au
This subject is not available as a general elective. To be eligible for enrolment, the subject must be specified in the students’ program structure.
Assurance of learning
Assurance of Learning means that universities take responsibility for creating, monitoring and updating curriculum, teaching and assessment so that students graduate with the knowledge, skills and attributes they need for employability and/or further study.
At Bond University, we carefully develop subject and program outcomes to ensure that student learning in each subject contributes to the whole student experience. Students are encouraged to carefully read and consider subject and program outcomes as combined elements.
Program Learning Outcomes (PLOs)
Program Learning Outcomes provide a broad and measurable set of standards that incorporate a range of knowledge and skills that will be achieved on completion of the program. If you are undertaking this subject as part of a degree program, you should refer to the relevant degree program outcomes and graduate attributes as they relate to this subject.
Subject Learning Outcomes (SLOs)
On successful completion of this subject the learner will be able to:
- Analyse BIM/Lean/IPD technology platforms to enhance design quality.
- Point out potential construction phase safety risks resulting from design approaches and initiate design adjustments to mitigate those risks.
- Distinguish between design content and quality requirements of various stakeholders via collaborative and integrated use of BIM/Lean/IPD project techniques and processes.
- Identify and estimate the risks of failure to ensure collaborative early identification and management of design content and quality standards, not only from a final design acceptance perspective, but also from the perspective of optimising safety aspects of all building operations.
|*In-Class Quiz - Individual||Online examination, multiple attemps allowable.||50%||To Be Negotiated||1, 2, 3, 4.|
|Presentation §||Team contribution and presentation||30%||Class stream dependent||2, 3, 4.|
|Presentation||Personal demonstration of knowledge||20%||Class stream dependent||2, 3, 4.|
- § Indicates group/teamwork-based assessment
- * Assessment timing is indicative of the week that the assessment is due or begins (where conducted over multiple weeks), and is based on the standard University academic calendar
- C = Students must reach a level of competency to successfully complete this assessment.
|High Distinction||85-100||Outstanding or exemplary performance in the following areas: interpretative ability; intellectual initiative in response to questions; mastery of the skills required by the subject, general levels of knowledge and analytic ability or clear thinking.|
|Distinction||75-84||Usually awarded to students whose performance goes well beyond the minimum requirements set for tasks required in assessment, and who perform well in most of the above areas.|
|Credit||65-74||Usually awarded to students whose performance is considered to go beyond the minimum requirements for work set for assessment. Assessable work is typically characterised by a strong performance in some of the capacities listed above.|
|Pass||50-64||Usually awarded to students whose performance meets the requirements set for work provided for assessment.|
|Fail||0-49||Usually awarded to students whose performance is not considered to meet the minimum requirements set for particular tasks. The fail grade may be a result of insufficient preparation, of inattention to assignment guidelines or lack of academic ability. A frequent cause of failure is lack of attention to subject or assignment guidelines.|
For the purposes of quality assurance, Bond University conducts an evaluation process to measure and document student assessment as evidence of the extent to which program and subject learning outcomes are achieved. Some examples of student work will be retained for potential research and quality auditing purposes only. Any student work used will be treated confidentially and no student grades will be affected.
Students must check the [email protected] subject site for detailed assessment information and submission procedures.
Policy on late submission and extensions
A student who has not established a basis for an extension in compliance with University and Faculty policy either by 1) not applying before the assessment due date or 2) by having an application rejected due to failure to show a justifiable cause for an extension, will receive a penalty on assessment submitted after its due date. The penalty will be 10% of marks awarded to that assessment for every day late, with the first day counted after the required submission time has passed. No assessment will be accepted for consideration seven calendar days after the due date. Where a student has been granted an extension, the late penalty starts from the new due date and time set out in the extension.
Policy on plagiarism
The University’s Academic Integrity Policy defines plagiarism as the act of misrepresenting as one’s own original work: another’s ideas, interpretations, words, or creative works; and/or one’s own previous ideas, interpretations, words, or creative work without acknowledging that it was used previously (i.e., self-plagiarism). The University considers the act of plagiarising to be a breach of the Student Conduct Code and, therefore, subject to the Discipline Regulations which provide for a range of penalties including the reduction of marks or grades, fines and suspension from the University.
Feedback on assessment
Feedback on assessment will be provided to students within two weeks of the assessment submission due date, as per the Assessment Policy.
If you have a disability, illness, injury or health condition that impacts your capacity to complete studies, exams or assessment tasks, it is important you let us know your special requirements, early in the semester. Students will need to make an application for support and submit it with recent, comprehensive documentation at an appointment with a Disability Officer. Students with a disability are encouraged to contact the Disability Office at the earliest possible time, to meet staff and learn about the services available to meet your specific needs. Please note that late notification or failure to disclose your disability can be to your disadvantage as the University cannot guarantee support under such circumstances.
Introduction to international standards for organising and digitisation of Building Information Modelling
Detailed review of case studies in different phases of construction
Practical exercises in extracting data from a BIM model
Conceptual versus constructible. Modelling as-is conditions based on laser scanning technologies
Fabrication level documentation overview and practical application
Using BIM for resource analysis and resource optimisation, practical application
QA site validation and product control for BIM-based projects
Model-based advanced practical exercises for Continuous Process Improvement