Understanding Buildings 2 extends the knowledge gained from Understanding Buildings 1. The environment and constraints impacting on a building construction project are analysed. Construction processes and materials common to many light industrial and commercial building projects are examined, including identification of interfaces and assessment of coordination requirements. Topics covered include underground services, in-situ concrete construction, structural steelwork, roofs, exterior walls, ceilings and partitions, installation of building services and internal finishes. Upon completion of this subject, students should be able to understand more complex construction processes, terminology and methodologies.
|Academic unit:||Faculty of Society & Design|
|Subject title:||Understanding Buildings 2|
Delivery & attendance
|Attendance and learning activities:||As successful completion of this subject is heavily dependent on participation during all scheduled sessions, attendance will be monitored. Most sessions build on the content of the previous one. It is difficult for a student to recover if a session is missed. It is the responsibility of the student to catch up on any content missed and to complete set work outside class. It is also necessary for students to engage proactively and contribute positively in discussions, analyses and case studies. The assessments are an important part of developing the knowledge and understanding required to fulfil the minimum requirements of this subject. In addition to ‘remote’ face-to-face contact time, students should plan to spend a minimum of 84 hours undertaking preparation/out of class work/personal study for this subject. This is intended as a general guide only for workload planning. More time may be required depending on the student's comprehension of the content delivered in class and aptitude for the subject. Please note that subsequent subjects assume the student has a full understanding of this subject - this content will not be repeated.|
|Prescribed resources:|| |
|[email protected] & Email:||[email protected] is the online learning environment at Bond University and is used to provide access to subject materials, lecture recordings and detailed subject information regarding the subject curriculum, assessment and timing. Both iLearn and the Student Email facility are used to provide important subject notifications. Additionally, official correspondence from the University will be forwarded to students’ Bond email account and must be monitored by the student.|
To access these services, log on to the Student Portal from the Bond University website as www.bond.edu.au
|Restrictions: ?|| This subject is not available to|
Assurance of learning
Assurance of Learning means that universities take responsibility for creating, monitoring and updating curriculum, teaching and assessment so that students graduate with the knowledge, skills and attributes they need for employability and/or further study.
At Bond University, we carefully develop subject and program outcomes to ensure that student learning in each subject contributes to the whole student experience. Students are encouraged to carefully read and consider subject and program outcomes as combined elements.
Program Learning Outcomes (PLOs)
Program Learning Outcomes provide a broad and measurable set of standards that incorporate a range of knowledge and skills that will be achieved on completion of the program. If you are undertaking this subject as part of a degree program, you should refer to the relevant degree program outcomes and graduate attributes as they relate to this subject.
Subject Learning Outcomes (SLOs)
On successful completion of this subject the learner will be able to:
- Identify construction industry participants and their roles;
- Interpret architectural and structural construction drawings, and extract information required;
- Describe critical construction compliance documents applicable to a project;
- Identify component parts of a commercial building (physically and on drawings) and their functions; and
- Recognise and describe common commercial construction processes.
|Case Study||Weekly inspection and research reports||20%||Progressive||2, 4, 5.|
|Written Report §||Major project based assignment||30%||Week 10||2, 3, 4, 5.|
|Take-home Examination||Timed take-home exam||50%||Week 12||1, 2, 3, 4, 5.|
Students must achieve a minimum 50% cumulative total for all assessment items to be eligible to pass this subject.
- § Indicates group/teamwork-based assessment
- * Assessment timing is indicative of the week that the assessment is due or begins (where conducted over multiple weeks), and is based on the standard University academic calendar
- C = Students must reach a level of competency to successfully complete this assessment.
|High Distinction||85-100||Outstanding or exemplary performance in the following areas: interpretative ability; intellectual initiative in response to questions; mastery of the skills required by the subject, general levels of knowledge and analytic ability or clear thinking.|
|Distinction||75-84||Usually awarded to students whose performance goes well beyond the minimum requirements set for tasks required in assessment, and who perform well in most of the above areas.|
|Credit||65-74||Usually awarded to students whose performance is considered to go beyond the minimum requirements for work set for assessment. Assessable work is typically characterised by a strong performance in some of the capacities listed above.|
|Pass||50-64||Usually awarded to students whose performance meets the requirements set for work provided for assessment.|
|Fail||0-49||Usually awarded to students whose performance is not considered to meet the minimum requirements set for particular tasks. The fail grade may be a result of insufficient preparation, of inattention to assignment guidelines or lack of academic ability. A frequent cause of failure is lack of attention to subject or assignment guidelines.|
For the purposes of quality assurance, Bond University conducts an evaluation process to measure and document student assessment as evidence of the extent to which program and subject learning outcomes are achieved. Some examples of student work will be retained for potential research and quality auditing purposes only. Any student work used will be treated confidentially and no student grades will be affected.
Students must check the [email protected] subject site for detailed assessment information and submission procedures.
Policy on late submission and extensions
A late penalty will be applied to all overdue assessment tasks unless an extension is granted in writing by the subject Lecturer. The standard late penalty will be 10% of available marks for that assessment per calendar day late, with no assessment to be accepted seven days after the due date. Students must complete an Application for Extension to Assessment Items form when requesting an extension. Where a student is granted an extension, the penalty of 10% per day late starts from the approved extended date.
Policy on plagiarism
University’s Academic Integrity Policy defines plagiarism as the act of misrepresenting as one’s own original work: another’s ideas, interpretations, words, or creative works; and/or one’s own previous ideas, interpretations, words, or creative work without acknowledging that it was used previously (i.e., self-plagiarism). The University considers the act of plagiarising to be a breach of the Student Conduct Code and, therefore, subject to the Discipline Regulations which provide for a range of penalties including the reduction of marks or grades, fines and suspension from the University.
Feedback on assessment
Feedback on assessment will be provided to students within two weeks of the assessment submission due date, as per the Assessment Policy.
Accessibility and Inclusion Support
If you have a disability, illness, injury or health condition that impacts your capacity to complete studies, exams or assessment tasks, it is important you let us know your special requirements, early in the semester. Students will need to make an application for support and submit it with recent, comprehensive documentation at an appointment with a Disability Officer. Students with a disability are encouraged to contact the Disability Office at the earliest possible time, to meet staff and learn about the services available to meet your specific needs. Please note that late notification or failure to disclose your disability can be to your disadvantage as the University cannot guarantee support under such circumstances.
Additional subject information
Students will be notified of all assessment grades (except final exam) through the "My Grades" link in iLearn.
The construction environment
In-situ concrete construction
Ceilings and partitions
Building services installation
Internal finishes, fixtures and fittings
Exterior building finishes and external works